Now Anton/Bauer goes back to it's roots in the film industry with the introduction of a new power source for Digital Cinema and film cameras.

The CINE-VCLX 560 watt hour power house has 2 regulated 28v outputs ( 3pin XLR ) and a 14v output ( 4pin XLR ) which can be used simultaneously and without switches. High rate NiMH cells provide up to 10 amps from the 28 volts channel and 20 amps from the 14 volt channel. CINE-VCLX also features a Realtime^TM display for accurate runtime indication.

A specialized CINE-VCLX-CA version, specifically designed for use with the Sony F-23 Cine Alta camera, supplies both 28 and 14 volts on a single cable, via an 8 pin Lemo connector along with a single 28 volt 3-pin and a 14 volt 4-pin.

The Cine Charger features full InterActive technology including six simultaneous charge termination systems, balance and rejuvenation modes, and LifeSaver Maintenance mode. The wide range mains input compatibility (90-250 VAC 50-60 Hz ) automatically adapts to any mains source worldwide.

CINE-VCLX- 560WH/38Ah, 14.4/28v simultaneous output NiMH battery
CINE-VCLX CA- 560WH/38Ah, 14.4/28v simultaneous output NiMH battery for Sony F23
12.70" x 5.53" x 9.96",25.95 lbs ( 32.27 x 14.03 x 25.29cm, 11.77 kg )

CINE VCLX CHARGER- Charger for Cine VCLX or Cine VCLX CA, charge time approx. 7 1/2 hours 10.25" x 2.25" x 8.50",4.2 lbs ( 26.03 x 5.71  x 21.59cm, 1.90 kg )

CINE-VCLX/2 Battery  280 watt hour dual simultaneous voltage output 14.4/ 28v output NiMH battery. CE approved 9.69" x 5.53" x 6.00" (24.62 x 14.05 x 15.24 cm) 14.85 lbs. (6.74 Kg)

CINE-VCLX/2 CHARGER- Battery charger for the CineVCLX/2 battery. Chargers one battery in approximately 3 hours. CE approved. 8.48" x 7.74" x 2.43" (21.54 x 19.66 x 6.17 cm) 2.5lbs. (1.14 Kg)

CS-GBC cable - Charger cable for the CINE-VCLX charger.

CA-F23 cable - 3 meter cable; 8 pin Lemo to 8 pin Lemo for Sony F23 Camera ( CINE-VCLX-CA only )

HARD CASE - Specially designed case to protect battery, charger and cable during transport.

CA-CCX - Charger cable for the CINE-VCLX /2  battery to CINEVCLX/2 charger.

CA-RED - Power cable for RED ONE camera; 4p XLR to 6p Lemo.

Links to more information:

- Cine VCLX owners Manual
- CINE AD

With RealTime display

DIONIC 160                                                          DIONIC 90

Dionic batteries are the perfect selection for the videographer with weight as the highest priority in selecting a battery. Dionic offers complete compatibility with PowerChargers already in the field (may require software chip update) and the Tandem series. Multiple electronic safety circuits, including the field proven reliability of the Digital Battery, and the mechanical integrity of IMPAC case construction have allowed Anton/Bauer to design an all new battery which safely employs lightweight cell chemistry for the rigors of Eng use. Dionic 90 weighs only 1.7 lbs (770 grams) and is the highest capacity lithium ion battery which can be legally transported without restriction under the IATA and DOT safety regulations. Dionic 160 contains an exclusive cell configuration unlike any other video battery. Instead of using cells originally designed for lighter duty applications, such as computers, this battery is constructed with specialized lithium ion cells originally designed for high rate military applications. Because of these low resistance cells, Dionic 160 can be used to power lighting loads and other accessories with a total output of up to 10 amps - a capability usually reserved only for nickel based chemistries. Dionic 160 weighs 30% less than a HyTRON 140, has 15% more capacity, and will run a typical camcorder for over 6 hours.

Digital DIONIC 160 Lithium Ion Battery 14.4V 160 WH

With RealTime display

NEW HyTron^TM140, previously offered only to select broadcasters, is the highest capacity battery in the industry not subject to transportation restrictions. It employs a special nickel metal hydride cell technology developed for the newest low emission vehicles and e-bikes.  This new cell design is exclusive to Anton/Bauer for the video industry and provides a capacity improvement greater than 40% compared to the HyTron 100.  Due to the robust nature of this cell, it outperforms in applications that leave other chemistries on the sidelines. Capable of loads up to 12 amps, the new HyTron 140 is uniquely able to handle the high current demands of HD cameras fully dressed with the latest production accessories.

Also, the NEW HyTron 100, the video industry's first high performance battery is back.  At 100 watt hours it out powers, out runs and outlives every NiCd or lithium ion battery out there.

The HyTRON system requires none of the "safety circuits" and performance limiting circuitry which lithium ion requires to operate safely. As a result of this, it does not require limiting when operating both a camera and on-camera UltrLight up to 85 watts (up to 175 watts total power). Choose HYTRON 140 or HyTron 100 for "All Morning/All Afternoon" shooting. Because of its advanced performance characteristics, HyTRON 140 and HyTron 100 are the only new technology batteries in the industry to carry the
MAXX IV Warranty.

Digital HyTRON 140 Nickel Metal Hydride Battery 14.4V 140 WH
5.45" x 4.75" x 2.90", 5.5 lbs., (13.84 x 12.06 x 7.37 cm, 2.5kg)
MAXX IV Warranty
Typical Runtimes:

3hrs. @45watts -  4 hrs. @35watts -  5.6hrs. @25watts

Digital HyTRON 100 Nickel Metal Hydride Battery 14.4V 100 WH
5.45" x 4.75" x 2.90", 5.5 lbs., (13.84 x 12.06 x 7.37 cm, 2.5kg)
MAXX IV Warranty

3hrs. @33watts - 4 hrs. @25watts - 5hrs. @20watts

The HyTRON 50 is particularly well suited for fast paced handheld operations, with on-camera lighting (up to 25 watts), taking advantage of its extremely small size, light weight, and long runtime.  Its 14.4 volt design optimizes performance in all environments. The HyTRON 50 is the perfect battery for professionals who are primarily concerned with the "economical performance in smallest package" benefit of new cell chemistries.

Digital HyTRON 50 Nickel Metal Hydride Battery 14.4V 50 WH
5-1/4" x 3 1/2" x 2-1/8", 1.9 lbs/.86 kg. (13.3 x 8.89 x 5.39cm, .88 kg)
HyTRON 50 has a 1 Year Warranty
MAXX II Warranty
HyTRON batteries should not be used with MP-4 and MP-8 chargers. Please
contact Anton/Bauer Customer Support.

Digital PRO PAC 14 with RealTime display

The Pro Pac is recognized by broadcasters and video professionals around the world as the ultimate professional video battery and is recommended for all applications. The premium low resistance Pro Pac cell is designed to deliver long life and high performance even under high current loads and the most adverse conditions.

The ProPac is the recommended battery when powering the ULTRALIGHT from the camcorder battery. The PRO PAC perfectly balances all professional hand-held camcorders on the shoulder resulting in an extremely integrated yet high energy and long run-time package. ProPac batteries feature the RealTime display which automatically detects camera load and calculates the batteries remaining runtime based on existing operating conditions.

Digital PRO PAC 14 Nickel Cadmium Battery 14.4V 65 WH
5.45" x 4.75" x 2.90", 5 lbs., (13.84 x 12.06 x 7.37 cm, 2.3kg)

Typical Runtimes:

• 2hrs.       @30watts
• 2.5hrs.    @25watts
• 4hrs.       @16watts

DIGITAL TRIMPAC 14 with RealTime display

The TRIMPAC size and shape was developed in close collaboration with major camcorder manufacturers. Thin, flat and lightweight (less than half the width and almost half the weight of a ProPac), the powerful low resistance TRIMPAC is the economical professional choice and will operate a 25 watt camcorder and on-camera light for up to 45 minutes.  TRIMPAC batteries feature the RealTime display which automatically detects camera load and calculates the batteries remaining runtime based on existing operating conditions.

Digital TRIMPAC 14 Nickel Cadmium Battery 14.4V 45 WH
6-3/8" x 4-13/16" x 1-5/8". 2-3/4 lbs, (16.1 x 12.2 x 4.1cm, 1.2 kg)

Typical Runtimes:

PRO PAC 14                                                    TRIMPAC 14

The Logic Series batteries below are virtually identical to their respective DIGITAL versions with respect to size, weight, capacity, IMPAC case construction, and application. The advanced MicroCode logic circuits and comprehensive ACS sensor networks of these batteries communicate directly with all Logic Series chargers providing the essential data critical for optimum performance, reliability, and life. These batteries do not, however, include the DIGITAL microprocessor features such as the "Fuel Computer", RealTime LCD display, and InterActive viewfinder "Fuel Gauge" circuit. 

PRO PAC 14
The Pro Pac is recognized by broadcasters and video professionals around the world as the ultimate professional video battery and is recommended for all applications. The premium low resistance Pro Pac cell is designed to deliver long life and high performance even under high current loads and the most adverse conditions.

The ProPac is the recommended battery when powering the ULTRALIGHT from the camcorder battery. The PRO PAC perfectly balances all professional hand-held camcorders on the shoulder resulting in an extremely integrated yet high energy and long run-time package. ProPac batteries feature the RealTime display which automatically detects camera load and calculates the batteries remaining runtime based on existing operating conditions.

PRO PAC 14 Nickel Cadmium Battery 14.4V 65 WH
5.45" x 4.75" x 2.90", 5 lbs., (13.84 x 12.06 x 7.37 cm, 2.3kg)

Typical Runtimes:

• 2hrs.      @30watts
• 2.5hrs.  @25watts
• 4hrs.       @16watts

TRIMPAC 14

The TRIMPAC size and shape was developed in close collaboration with major camcorder manufacturers. Thin, flat and lightweight (less than half the width and almost half the weight of a ProPac), the powerful low resistance TRIMPAC is the economical professional choice and will operate a 25 watt camcorder and on-camera light for up to 45 minutes.  TRIMPAC batteries feature the RealTime display which automatically detects camera load and calculates the batteries remaining runtime based on existing operating conditions.

TRIMPAC 14 Nickel Cadmium Battery 14.4V 45 WH
6-3/8" x 4-13/16" x 1-5/8". 2-3/4 lbs, (16.1 x 12.2 x 4.1cm, 1.2 kg)

Typical Runtimes:

• 1.5hrs.   @25watts
• 2.5hrs.   @17watts
• 3.75hrs.  @12watts

Quad 2702

The four position QUAD PowerCharger is the most advanced power system ever available. PowerCharger provides all of the advanced charging techniques of the Anton/Bauer InterActive 2000 system in a lightweight package the size of a notebook computer. Six full-time operating charge terminations - TCO, -ΔV, temperature compensated VCO, DT/dt, CCO and FUL- (versus one for conventional chargers) deliver the unmatched battery performance and reliability. Because all programming is contained on a single field replaceable chip, PowerCharger ensures future compatibility to new cell technologies and charging methods. The Quad PowerCharger will sequentially charge any combination of Anton/Bauer Gold Mount batteries. QUAD PowerChargers have an integral recessed carry handle to easily transport batteries and charger to and from location.

The 70 watt QUAD 2702 features a multi-function LCD, wide range mains input (90-250VAC 50/60Hz) serial output port, a  built in 2 amp DDM Diagnostic/Discharge Module and a high power 70 watt camera supply output which will power virtually all field equipment from AC mains, making it an all purpose power and battery analyzer system.

QUAD 2702 PowerCharger includes DDM and 70 watt supply.

• 90-250VAC wide range input.
• Size: 8" X 12.5" X 2.75" (20.3 X 31.7 X 7 cm). Weight: 4.1 lbs. (1.8kg)

Optional Accessories:  XLR-4 (not included)

Dual 2722

The  DUAL 2722 PowerCharger puts all the performance and advanced charging techniques of the Anton/Bauer InterActive 2000 PowerCharger into a compact two-position simultaneous charger. DUAL PowerCharger can charge any combination of Anton/Bauer Gold Mount batteries employing six charge termination algorithms for unsurpassed safety and reliability. The small size and versatility of the DUAL PowerCharger makes it the ideal PowerCharger for professionals who travel often. The 70 watt DUAL 2722 features simultaneous charging, multi-function LCD, wide range mains input (90-250VAC 50/60 Hz) serial output port, a built in DDM Diagnostic/Discharge Module and a high power 70 watt camera supply output which will power virtually all field equipment from AC mains.

Dual 2722 Simultaneous PowerCharger includes DDM and 70 watt supply.

• 90-250VAC wide range input.
• Size: 8" X 9.25" X 3.25" (20.3 X 23.5 X 8.2 cm. Weight: 2.85 lbs. (1.3kg)

Optional Accessories:  XLR-4 (not included)

XLR-4

 Camera Power XLR-4 Accessory Cable 10 ft / 3.04m cable connects to any PowerCharger or T2 model to power camera / camcorder through standard camera 4-pin XLR input. Heavy duty wire gauge cable and high quality connectors minimize losses.

More on Cables

TWQ

The TWQ is a four position simultaneous InterActive charger which delivers the ability to charge FOUR batteries at the same time, conveying the full complement of batteries up to 4 times faster than some sequencing type chargers. Focusing the full capability of the efficiency of the T series power architecture on battery charging, the TWQ uses all the charge termination techniques of the field proven InterActive system to service any of the Anton/Bauer Gold Mount batteries quickly, reliably, and safely. Simultaneous charging means that all batteries on the charger will be completed in the time shown on the chart  (catalog page 8) (e.g. four ProPac batteries will be charged in 3 1/2 hours) versus sequencing the batteries one at a time. This is the perfect charger for the operation which needs to cycle batteries often during the shooting day. Like all InterActive chargers, TWQ will address all Anton/Bauer batteries of any chemistry.

T2

The T2 combines two channel independent simultaneous InterActive charging with a 70 watt DC output for camera operation. The T2 is capable of simultaneously operating the most power-hungry camera while charging up a spare battery in the fastest charge time possible. InterActive charge programming provides all charge termination and protection routines for safe, reliable, chemistry independent charging. T2 automatically identifies battery type and chemistry adjusting the charge process for each battery. T2 will address all Anton/Bauer Gold Mount batteries including HyTRON and Dionic. T2's simultaneous charging reduces the time to obtain two fully charged batteries versus sequential charging (see chart on page 8), charging two batteries in the time it takes a sequencing charger to address one battery. T2 meets all applicable standards including CE and FCC requirements.

T2 simultaneous two position InterActive charger with 70 watt camera output.

Optional Accessories:  XLR-4 (not included)

TWIN

TWIN Two position, 60-watt simultaneous InterActive® battery charger
The sleek design of the TANDEM has been applied to the TWIN charger making it the lightest and smallest charger Anton/Bauer has ever produced. Its high impact plastic enclosure will stand up to the most rugged use. Its universal wide range mains input (90-250 VAC 50/60Hz) makes it the ideal travel charger.
TWIN features the same exclusive state-of-the-art charge termination techniques of Anton/Bauer InterActive® chargers with the added advantage of charging two batteries at the same time! TWIN will charge two TrimPacs in 2 hours or HyTRON 50s in 3 hours, two ProPacs in 3 1/2 hours, or two Dionic 90's in 5 1/2 hours. The exclusive Anton/Bauer Lifesaver® maintenance routine keeps all batteries fully charged until ready for use.

The TWIN is chemistry independent and capable of upgrade with a simple chip replacement as new battery technologies are introduced. Batteries are automatically identified by the charger and addressed with a charge routine specifically designed for that battery to reliably and safely optimize battery performance and service life.

TWIN Two position, 30-watt simultaneous InterActive® battery charger.

TANDEM 70

Tandem 70 Gold Mount 70 watt charger / power supply.
A new approach to portable power, Tandem combines all the functionality of a one position InterActive® charger with the convenience of a noise free camera mounted wide range AC mains adapter. Tandem will power even the most power hungry high definition camera from any worldwide AC source. It also doubles as a full function InterActive Charger charging any Anton/Bauer Gold Mount battery in two hours or less. Weighing only one pound (.450 grams) the Tandem 70 is the perfect addition to any field camera and a lightweight mains adapter and a high performance charger. Meets all applicable regulatory requirements including CE and FCC.

Tandem 70 Gold Mount 70 watt charger / power supply.